ConfigurazioneEthernetLxcSerraX - Cronologia

Rakk: cat

2017-04-30T05:14:51Z

cat

← Versione meno recente		Versione delle 05:14, 30 apr 2017
Riga 73:		Riga 73:
	rc-update add wpa_supplicant default		rc-update add wpa_supplicant default
	</pre>		</pre>

			[[Categoria:EigenNet]]
			[[Categoria:Device Mobili]]
			[[Categoria:HowTo]]

G10h4ck: /* Create the ethernet interface for your LXC container (on the phisical machine) */

2013-03-26T14:43:04Z

Create the ethernet interface for your LXC container (on the phisical machine)

← Versione meno recente		Versione delle 14:43, 26 mar 2013
Riga 15:		Riga 15:
	lxc.network.flags = up		lxc.network.flags = up
	## Followings 3 line depends on the machine so you MUST change them!!		## Followings 3 line depends on the machine so you MUST change them!!
	lxc.network.ipv4 = 131.114.X.Z/29		lxc.network.ipv4 = 131.114.186.Z/29
	lxc.network.ipv4.gateway = 131.114.X.1		lxc.network.ipv4.gateway = 131.114.186.1
	lxc.network.hwaddr = 26:99:38:32:f3:19		lxc.network.hwaddr = 26:99:38:32:f3:19
	</pre>		</pre>

G10h4ck: /* Configure wpa_supplicant ( on the LXC container ) */

2013-03-26T14:38:04Z

Configure wpa_supplicant ( on the LXC container )

← Versione meno recente		Versione delle 14:38, 26 mar 2013
Riga 43:		Riga 43:

	<pre>		<pre>
	wpa_supplicant_args="-ieth2 -Dwired ~~-c/etc/wpa_supplicant/wpa_supplicant.eth2.conf~~"		wpa_supplicant_args="-ieth2 -Dwired"
	</pre>		</pre>

	Edit /etc/wpa_supplicant/wpa_supplicant~~.eth2~~.conf it should appear like this		Edit /etc/wpa_supplicant/wpa_supplicant.conf it should appear like this
	<pre>		<pre>
	# IEEE 802.1X works with EAPOL version 2, but the version is defaults		# IEEE 802.1X works with EAPOL version 2, but the version is defaults
Riga 66:		Riga 66:
	}		}
	</pre>		</pre>


	===Make wpa_supplicast start automagically at boot ( on the LXC container )===		===Make wpa_supplicast start automagically at boot ( on the LXC container )===

G10h4ck: /* Create the ethernet interface for your LXC container (on the phisical machine) */

2013-03-25T14:22:46Z

Create the ethernet interface for your LXC container (on the phisical machine)

← Versione meno recente		Versione delle 14:22, 25 mar 2013
Riga 15:		Riga 15:
	lxc.network.flags = up		lxc.network.flags = up
	## Followings 3 line depends on the machine so you MUST change them!!		## Followings 3 line depends on the machine so you MUST change them!!
	lxc.network.ipv4 = 131.114.~~251~~.~~239~~/23		lxc.network.ipv4 = 131.114.X.Z/29
	lxc.network.ipv4.gateway = 131.114.~~250~~.1		lxc.network.ipv4.gateway = 131.114.X.1
	lxc.network.hwaddr = 26:99:38:32:f3:19		lxc.network.hwaddr = 26:99:38:32:f3:19
	</pre>		</pre>


	===Configure the virtual interface ( on the LXC container )===		===Configure the virtual interface ( on the LXC container )===

G10h4ck: Creata pagina con '==Attach your Gentoo LXC container to Serra with 802.1X authentication== ===Create the ethernet interface for your LXC container (on the phisical machine)=== Edit /etc/lxc/...'

2013-03-23T11:05:46Z

Creata pagina con '==Attach your Gentoo LXC container to Serra with 802.1X authentication== ===Create the ethernet interface for your LXC container (on the phisical machine)=== Edit /etc/lxc/...'

Nuova pagina

==Attach your Gentoo LXC container to Serra with 802.1X authentication==

===Create the ethernet interface for your LXC container (on the phisical machine)===

Edit /etc/lxc/YourLxcContainerName.conf adding lines inspired to the following

<pre>
## Virtual itnerface type
lxc.network.type = macvlan
## Phisical ( on the phisical machine ) interface name attacched to serra
lxc.network.link = eth2
## Virtual ( on the LXC container ) interface name attacched to serra
lxc.network.name = eth2
lxc.network.flags = up
## Followings 3 line depends on the machine so you MUST change them!!
lxc.network.ipv4 = 131.114.251.239/23
lxc.network.ipv4.gateway = 131.114.250.1
lxc.network.hwaddr = 26:99:38:32:f3:19
</pre>

===Configure the virtual interface ( on the LXC container )===

Edit /etc/conf.d/net, the eth2 configuration should appear like this

<pre>
# serra
config_eth2=" null"
</pre>

===Install the 802.1X authenticaticator ( on the LXC container )===

To autenticate with 802.1X you need wpa_supplicant, to install it run
<pre>
emerge -avq net-wireless/wpa_supplicant
</pre>

===Configure wpa_supplicant ( on the LXC container )===

Edit /etc/conf.d/wpa_supplicant it should appear like this

<pre>
wpa_supplicant_args="-ieth2 -Dwired -c/etc/wpa_supplicant/wpa_supplicant.eth2.conf"
</pre>

Edit /etc/wpa_supplicant/wpa_supplicant.eth2.conf it should appear like this
<pre>
# IEEE 802.1X works with EAPOL version 2, but the version is defaults
# to 1 because of compatibility problems with a number of wireless
# access points. So we explicitly set it to version 2:
eapol_version=2

# When configuring WPA-Supplicant for use on a wired network, we don?t need to
# scan for wireless access points. See the wpa-supplicant documentation if
# you are authenticating through 802.1x on a wireless network:
ap_scan=0

network={
key_mgmt=IEEE8021X
eap=PEAP
phase2="auth=MSCHAPV2"
identity="yourLogin"
password="yourPassword"
}
</pre>

===Make wpa_supplicast start automagically at boot ( on the LXC container )===

Ad wpa_supplicant to the default runlevel running
<pre>
rc-update add wpa_supplicant default
</pre>